[2021.6] Update! New, Free | Fortinet NSE7_EFW-6.2 Practice Test, Fortinet NSE7_EFW-6.2 Pdf

Get the newest free complete Fortinet NSE7_EFW-6.2 exam dumps! Go https://www.pass4itsure.com/nse7_efw-6-2.html (Q&As: 102 ). Best 100% valid up-to-date actual Fortinet NSE7_EFW-6.2 dumps that bring you the best results. You can get 100% free updates on Fortinet NSE7_EFW-6.2 practice test questions, Fortinet NSE7_EFW-6.2 pdf here.

[free pdf] Fortinet NSE7_EFW-6.2 pdf download from google drive https://drive.google.com/file/d/1lw2A51jUlDv9TfqfhQZ6BEEocwVOT4Tg/view?usp=sharing

Latest Fortinet NSE7_EFW-6.2 Exam Questions From Youtube

https://youtu.be/-kSg9jnShxM

New Fortinet NSE7_EFW-6.2 Practice Test Q1-Q13 Free

QUESTION 1
Examine the output of the `get router info bgp summary\\’ command shown in the exhibit; then answer the question
below.

NSE7_EFW-6.2 exam questions-q1

Which statements are true regarding the output in the exhibit? (Choose two.)
A. BGP state of the peer 10.125.0.60 is Established.
B. BGP peer 10.200.3.1 has never been down since the BGP counters were cleared.
C. Local BGP peer has not received an OpenConfirm from 10.200.3.1.
D. The local BGP peer has received a total of 3 BGP prefixes.
Correct Answer: AC

QUESTION 2
View the exhibit, which contains the partial output of an IKE real-time debug, and then answer the question below.

NSE7_EFW-6.2 exam questions-q2

Why didn\\’t the tunnel come up?
A. The pre-shared keys do not match.
B. The remote gateway\\’s phase 2 configuration does not match the local gateway\\’s phase 2 configuration.
C. The remote gateway\\’s phase 1 configuration does not match the local gateway\\’s phase 1 configuration.
D. The remote gateway is using aggressive mode and the local gateway is configured to use man mode.
Correct Answer: C

QUESTION 3
A FortiGate\\’s portal is connected to a private network. Its port2 is connected to the Internet. Explicit web proxy is
enabled in port1 and only explicit web proxy users can access the Internet. Web cache is NOT enabled. An internal web
proxy user is downloading a file from the Internet via HTTP. Which statements are true regarding the two entries in the
FortiGate session table related to this traffic? (Choose two.)
A. Both session have the local flag on.
B. The destination IP addresses of both sessions are IP addresses assigned to FortiGate\\’s interfaces.
C. One session has the proxy flag on, the other one does not.
D. One of the sessions has the IP address of port2 as the source IP address.
Correct Answer: AD


QUESTION 4
Examine the output of the `diagnose sys session list expectation\\’ command shown in the exhibit; then answer the
question below.

NSE7_EFW-6.2 exam questions-q4

Which statement is true regarding the session in the exhibit?
A. It was created by the FortiGate kernel to allow push updates from FotiGuard.
B. It is for management traffic terminating at the FortiGate.
C. It is for traffic originated from the FortiGate.
D. It was created by a session helper or ALG.
Correct Answer: D

QUESTION 5
The logs in a FSSO collector agent (CA) are showing the following error: failed to connect to registry: PIKA1026
(192.168.12.232)
What can be the reason for this error?
A. The CA cannot resolve the name of the workstation.
B. The FortiGate cannot resolve the name of the workstation.
C. The remote registry service is not running in the workstation 192.168.12.232.
D. The CA cannot reach the FortiGate with the IP address 192.168.12.232.
Correct Answer: C
https://kb.fortinet.com/kb/documentLink.do?externalID=FD30548
QUESTION 6
When does a RADIUS server send an Access-Challenge packet?
A. The server does not have the user credentials yet.
B. The server requires more information from the user, such as the token code for two-factor authentication.
C. The user credentials are wrong.
D. The user account is not found on the server.
Correct Answer: B

QUESTION 7
Examine the output of the `get router info OSPF neighbor\\’ command shown in the exhibit; then answer the question
below.

NSE7_EFW-6.2 exam questions-q7

Which statements are true regarding the output in the exhibit? (Choose two.)
A. The interface ToRemote is OSPF network type point-to-point.
B. The OSPF router with the ID 0.0.0.2 is the designated router for the ToRemote network.
C. The local FortiGate is the backup designated router for the wan1 network.
D. The OSPF routers with the IDs 0.0.0.69 and 0.0.0.117 are both designated routers for the wan1 network.
Correct Answer: AC
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13685-13.html


QUESTION 8
View the exhibit, which contains the output of a diagnose command, and then answer the question below.

NSE7_EFW-6.2 exam questions-q8

Which statements are true regarding the output in the exhibit? (Choose two.)
A. FortiGate will probe 121.111.236.179 every fifteen minutes for a response.
B. Servers with the D flag are considered to be down.
C. Servers with a negative TZ value are experiencing a service outage.
D. FortiGate used 209.222.147.3 as the initial server to validate its contract.
Correct Answer: AD
A ? because the flag is Failed so FortiGate will check if a server is available every 15 min D-state is I, contact to validate
contract info

QUESTION 9
View the exhibit, which contains the output of a diagnose command, and answer the question below.

NSE7_EFW-6.2 exam questions-q9

Which statements are true regarding the Weight value?
A. Its initial value is calculated based on the round trip delay (RTT).
B. Its initial value is statically set to 10.
C. Its value is incremented with each packet lost.
D. It determines which FortiGuard server is used for license validation.
Correct Answer: C


QUESTION 10
An administrator has configured a dial-up IPsec VPN with one phase 2, extended authentication (XAuth)
and IKE mode configuration. The administrator has also enabled the IKE real-time debug:
diagnose debug application like-1
diagnose debug enable
In which order is each step and phase displayed in the debug output each time a new dial-up user is
connecting to the VPN?
A. Phase1; IKE mode configuration; XAuth; phase 2.
B. Phase1; XAuth; IKE mode configuration; phase2.
C. Phase1; XAuth; phase 2; IKE mode configuration.
D. Phase1; IKE mode configuration; phase 2; XAuth.
Correct Answer: B
https://help.fortinet.com/fos50hlp/54/Content/FortiOS/fortigate-ipsecvpn-54/IPsec_VPN_Concepts/IKE_Packet_Processing.htm

QUESTION 11
What global configuration setting changes the behavior for content-inspected traffic while FortiGate is in the system
conserve mode?
A. av-failopen
B. mem-failopen
C. utm-failopen
D. ips-failopen
Correct Answer: A
https://help.fortinet.com/fos50hlp/54/Content/FortiOS/fortigate-security-profiles- 54/Other_Profile_Considerations/Conserve%20mode.htm


QUESTION 12
When using the SSL certificate inspection method to inspect HTTPS traffic, how does FortiGate filter web requests
when the client browser does not provide the server name indication (SNI) extension?
A. FortiGate uses the requested URL from the user\\’s web browser.
B. FortiGate uses the CN information from the Subject field in the server certificate.
C. FortiGate blocks the request without any further inspection.
D. FortiGate switches to the full SSL inspection method to decrypt the data.
Correct Answer: B

QUESTION 13
Which two tasks are automated using the Install Wizard on FortiManager? (Choose two.)
A. Preview pending configuration changes for managed devices.
B. Add devices to FortiManager.
C. Import policy packages from managed devices.
D. Install configuration changes to managed devices.
E. Import interface mappings from managed devices.
Correct Answer: AD
https://help.fortinet.com/fmgr/50hlp/56/5-6-2/FortiManager_Admin_Guide/1000_Device%
20Manager/1200_install_to%20devices/0400_Install% 20wizard-device%20settings.htm There are 4 main wizards: Add
Device: is used to add devices to central management and import their configurations. Install: is used to install
configuration changes from Device Manager or Policies and Objects to the managed devices. It allows you to preview
the changes and, if the administrator doesn\\’t agree with the changes, cancel and modify them. Import policy: is used to
import interface mapping, policy database, and objects associated with the managed devices into a policy package
under the Policy and Object tab. It runs with the Add Device wizard by default and may be run at any time from the
managed device list. Re-install policy: This is used to perform a quick install of the policy package. It doesn\\’t gives the ability
to preview the changes that will be installed to the managed device.

You can also browse the Fortinet NSE7_EFW-6.2 exam practice questions updated in other months! click here [2021.4] New, Free | Fortinet NSE7_EFW-6.2 Practice Test, Fortinet NSE7_EFW-6.2 Pdf

Fortinet NSE7_EFW-6.2 PDF Free Download

Fortinet NSE7_EFW-6.2 pdf 100% free https://drive.google.com/file/d/1lw2A51jUlDv9TfqfhQZ6BEEocwVOT4Tg/view?usp=sharing

Pass4itsure Special Discount Share:

Pass4itsure Fortinet exam 15% discount with coupon: Fortinet

Finish:

Free share latest Fortinet NSE7_EFW-6.2 pdf, Fortinet NSE7_EFW-6.2 practice questions, Fortinet NSE7_EFW-6.2 exam video!

Latest Fortinet NSE7_EFW-6.2 questions answers in order to lead every candidate towards a brighter and better future. Select https://www.pass4itsure.com/nse7_efw-6-2.html to get complete Fortinet NSE7_EFW-6.2 dumps practice exam questions and answers. Wish you success!

Fortinet NSE7_EFW-6.2 pdf free download https://drive.google.com/file/d/1lw2A51jUlDv9TfqfhQZ6BEEocwVOT4Tg/view?usp=sharing