This volume is part of the Exam Certification Guide Series from Cisco 642-176.Cisco 642-176 in this series provide officially developed exam preparation materials that offer assessment, review, and practice to help Cisco 642-176 Certification candidates identify weaknesses, concentrate their study efforts, and enhance their confidence as Cisco 642-176 exam day nears.
Refer to the exhibit. What could be possible causes for the “Serial0/0 is down” interface status? (Choose two.)
A. A Layer 1 problem exists.
B. The bandwidth is set too low.
C. A protocol mismatch exists
D. An incorrect cable is being used.
E. There is an incorrect IP address on the Serial 0/0 interface.
Correct Answer: AD
Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information? (Choose two.)
A. the amount of available ROM
B. the amount of available flash and RAM memory
C. the version of the bootstrap software present on the router
D. show version
E. show processes
F. show running-config
Correct Answer: BD
Refer to the exhibit. Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and Switch2 trunk ports must be configured using the same encapsulation type.
Correct Answer: DF
Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
“Everything is under control” – www.pass4sure.com 3
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
Correct Answer: BC
If you are a network administrator, how will you explain VTP configuration to a new technician? (Choose three.)
A. In the VTP client mode, a switch is unable to update its local VLAN database.
B. Configure a trunk link between the switches to forward VTP updates.
C. In the VTP server mode, a switch is able to update a switch in the VTP transparent mode.
D. In the VTP transparent mode, a switch will forward the received updates to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.
Correct Answer: ABD
Cisco IOS (originally Internetwork Operating System) is the software used on the vast majority of Cisco Systems routers and all current Cisco network switches. Which two of the following devices could you configure as a source for the IOS image in the boot system command? (Choose two.)
C. flash memory
D. HTTP server
E. TFTP server
F. Telnet server
Correct Answer: CE
CCNA Composite Exam:Cisco 642-176 CCNAX is the composite exam associated with the Cisco CCNA Routing and Switching certification. Candidates can prepare for this exam by taking the Interconnecting Cisco Networking Devices: Accelerated (CCNAX) course. This exam tests a candidate’s knowledge and skills required to install, operate, and troubleshoot a small to medium size enterprise branch network. The topics include all the areas covered under ICND 1 and ICND2 Exams.
What are two reasons a network administrator would use CDP? (Choose two.)
A. to obtain VLAN information from directly connected switches
B. to determine the status of network services on a remote device
C. to determine the status of the routing protocols between directly connected routers
D. to verify the type of cable interconnecting two devices
E. to verify Layer 2 connectivity between two devices when Layer 3 fails “Everything is under control” -www.pass4sure.com 5
F. to obtain the IP address of a connected device in order to telnet to the device
Correct Answer: EF
Refer to the exhibit. Both switches are using a default configuration. Which two destination addresses will host 4 use to send data to host 1? (Choose two.)
“Everything is under control” – www.pass4sure.com 6
A. the IP address of host 1
B. the IP address of host 4
C. the MAC address of host 1
D. the MAC address of host 4
E. the MAC address of the Fa0/0 interface of the R1 router
F. the MAC address of the Fa0/1 interface of the R1 router
Correct Answer: AF
“Everything is under control” – www.pass4sure.com 7
Refer to the exhibit. The router has been configured with these commands:
What are the two results of this configuration? (Choose two.)
A. The default route should have a next hop address of 220.127.116.11.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers.
D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet “Everything is under control” – www.pass4sure.com 8 without address translation.
Correct Answer: DE
Your Company has installed IP phones. Both the phones and the office computers connect to the same device. The phone traffic and the office computer data traffic must be on different networks to ensure maximum throughput for the phone data. Which network device can be best connected to the phones and computers, and which technology will be performed on this device? (Choose two.)
Correct Answer: CF
The VVJHV contains more than 400 practice questions for the Cisco 642-176 exams, including simulation-based questions. Also contains hands-on exercises and a customized copy of the Cisco 642-176 exams network simulation software.